** special promotion** TYGA-VHM-carbon performance set, Suzuki RGV250 Aprilia RS250

1.654,20

TYGA – Conjunto de alto rendimiento VHM, Suzuki RGV250 – Aprilia RS250
Para aquellos que quieren el conjunto perfecto! Rendimiento y miradas !!!
Juego completo de escape de acero inoxidable (estilo GP a elección o estilo SBS)

Juego completo de culatas
VHM Silenciadores de carbono o de carbono / kevlar (2 piezas)
Este juego completo que ofrecemos ahora por el precio muy especial

Nota: La imagen muestra silenciadores de aluminio, esto sería carbono o carbon / kevlar

** special promotion** VHM-BILLET powervalve set, Suzuki RGV250 Aprilia RS250

939,01

** Promoción especial ** VHM – BILLET Powervalve set, Suzuki RGV250 Aprilia RS250 
Set completo de afinación para tus 2 tiempos. 
El kit contiene: 

2x VHM culatas

2x inserciones standard de culatas VHM.

2 valvulas de escape Billet izquierdo 
2x valvulas de escape Billet derecho 

Este conjunto es una necesidad para todos los propietarios de RS y RGV. 
Las valvulas de escape CNC de billet se prueban completamente en DYNO, también en motos de pista y de calle. 
Creo que VHM no necesita más introducción, pero vea el video a continuación. 
Ahora ofrecemos este set por un precio inmejorable. 

2T blank plug, NSR250

8,92

Replaces the 2T oil injector pump for pre mix use. Secure with liquid gasket such as Three Bond 1104. Must be used with TYLY-0015 Plug holder

Note for blocking the extra 2T feed on later model oil pumps.

On later engines (some MC21 and all MC28, there is an extra oil feed to the cases which can be observed when the oil pump is removed. HRC used to supply a little aluminium plug that you knocked into this extra hole to blank it off. However, that is discontinued so what to do depends on whether the conversion to pre-mix is permanent or not.

If permanant, then we recommend you make sure it’s all clean and degreased, and then fill the hole with epoxy steel. Allow it to cure and it’ll never leak.

If you’re not sure if you’ll ever go back to the oil pump, but would like the option, then we suggest covering the hole with a small thin disc of steel or plastic, and then using a RTV sealant to sort of glue that in place and also block it off. The RTV will stop any leaks, and the small disc will stop any RTV going down the hole. This is then soft enough to be cut away at a later date should you need to.

Compatible products:

TYLY-0015 Plug holder

Collar/manifold Special , NSR250

75,48

This is a special replacement part for the NSR250. The manifold has a CNC machined profile, matching the exhaust port exit to allow smooth exhaust gas transition from the cylinder into the expansion chamber. This helps to increase performance from as little as 7,000rpm all the way up to and beyond peak power.

Stephen A’lee of George White Superbikes in the UK independently dyno tested the manifolds on a stock engine MC21, with Stock airbox. The only mods were TYGA pipes.

The red trace shows the above bike using the supplied EXMN-0003 manifold with a peak of 57.2hp.

The blue trace shows the same bike with EXMN-9003 special manifolds fitted. A gain of 1.4hp with no jetting changes.

Compatible with the following TYGA system:

EXCS-0003

EXCS-0005

EXCS-0006

culatas vhm RGV250 / RS250 (2 piezas sin insert)

659,33

APRILIA RS250

SUZUKI RGV25 VJ22

La famosas culatas de oro de VHM cámara de combustión intercambiable ( insert) está especialmente desarrollado para la salida de potencia óptima durante toda la carrera y tiene un conducto de agua mejorada. Se fabrica a partir de una aleación de alta calidad y las juntas tóricas se utilizan para el sellado. Dos juntas tóricas Ø94.97×1.78 están incluidos.

Utilice insert AE32149

  • Más potencia del motor
  • Mejor transferencia de calor
  • Más resistencia a la detonación
  • cámaras de combustión intercambiables disponibles

¡¡¡ Los insert se deben pedir por separado no están incluidos ¡¡¡

 Dos juntas tóricas Ø94.97×1.78 están incluidas.

GPS blank plug, NSR250

18,14

Replaces Gear Position Sensor for race use. Secure with liquid gasket such as Three Bond 1104. Must be used with TYLY-0015 Plug holder

Compatible products

TYLY-0015 Plug holder

Ignition rotor (track only), Honda NSR250 MC21/MC28

245,81

HRC style total loss ignition rotor for the NSR250 MC28.

Simply remove the standard rotor and generator system and fit this super light weight rotor.

Timing position is the same as standard MC28 rotor, but this can of course be adjusted by offset woodruff keys.

For use on NSR250 MC21 an offset woodruff key (2 degree advanced) must be used.

Please note that this rotor is for racing only and cannot be used on the street. It’s use requires that the battery be fully charged and in tip top condition as the charging system is removed and performance relies solely on the battery condition.

INSERT CULATA VHM , Suzuki RGV250 / Aprilia RS250

64,07

INSERT PARA CULATAS VHM

APRILIA RS250

SUZUKI RGV250

La cámara de combustión se puede ajustar rápidamente dependiendo de las condiciones de la pista y de tiempo, ya que los insert son fáciles de cambiar. Los insert están hechos de aluminio de aleación aeronáutica para la resistencia a la detonación. Hay varios insertos con diferentes volúmenes disponibles para cada cabeza.

  • Rápida para ajustar
  • Muchas opciones estándar de VHM, opcional, ciegos
  • especificaciones personalizadas posibles

Estos insert de culatas VHM no se ajustan a las culatas originales, sólo a nuestras culatas VHM!

Mas info de insert en

https://www.vhm.nl/en/page/vhm-parts-info/inserts

Powervalve cover blue, RGV250 / RS250

145,74

Estas tapas de válvula de escape TYGA de aluminio 6061 T6 ofrecen una gran mejora estética del motor y también cumplen la función de mantener el área de la cámara de la válvula libre de residuos de escape.
El aceite residual se almacena en un bote para que sea mas cómodo el vaciado.
El sellado de la cubierta del cilindro se realiza mediante una ranura mecanizada por CNC equipada con una junta tórica, por lo que no hay más juntas rotas. Tornillos de acero inoxidable M5.

Este kit incluye las siguientes partes:

2x tapas
2x juntas tóricas
8x M5 tornillos de cabeza Botón
2x manguera
1x botella de captura

Mostrando 1–12 de 16 resultados